What does LC mean on Whirlpool washer?

Answer

If the control lock has been enabled, the control will no longer work as intended. In the event that you attempt to press buttons, you may see the code “LoC” or “LC” (depending on your model). This is a reminder that you have activated the control lock and that you must deactivate it in order for the washer controls to operate properly.

As a result, how can I get rid of the problem code on my Whirlpool washing machine?

Press the stop or cancel button twice, followed by the power button once, to delete the code. If the code is still on the screen, unplug the washer or turn off the power for one minute to clear it. During the Clean Washer cycle, it was discovered that there were items in the washer. Items should be removed from the drum before starting the Clean Washer cycle a second time.

Also, why does my washer have the word Loc on it?

Controls have been locked, as shown by the letters (LOC). For further security, press OPTIONS and SELECT at the same time until the Control (Control Lock) indication is illuminated to prevent someone from mistakenly starting or stopping the washer. In order to disable the controls, simultaneously press OPTIONS and SELECT until the Control (Control Lock) indication turns off.

Furthermore, how can I unlock my Whirlpool washing machine?

The “Drain and Spin” button on the washer’s control panel should be pressed to make an effort to unlock the machine. This may help to drain any excess water that may have built up and caused the machine to get locked. It should be possible to open the door when the “Drain and Spin” cycle is complete.

What is the best way to reset my Whirlpool front-load washer?

Unplug the machine for 30 seconds to see whether the Duet washer control can be reset that way. Manually unlocking the washer may be accomplished by removing the top panel (remove the screws on the rear of the top panel and sliding the top panel back to pull the washer out).

There were 25 related questions and answers found.

What exactly is the problem with my Whirlpool washer?

The washer comes to a halt because it is taking an excessive amount of time to drain the water. This is frequently caused by a blockage in the drain line or by anything impeding the pump’s ability to function. If following these instructions does not resolve the issue, it is possible that the washer’s water pump may need to be replaced.

What does the Code F on a Whirlpool washing machine mean?

The “F” error number indicates a problem with the washing machine’s system, sometimes known as “Fault.” The “E” error code indicates which component in your washer is producing the problem or “Error.” Generally speaking, these “F” error codes indicate the following… – The F1 error code on a Whirlpool Duet washing machine indicates a problem with the main control board and/or software.

What is the best way to remove the kid lock from my Whirlpool washer?

To activate and deactivate the Control Lock, press the button that corresponds to that specific key. Control Lock may be turned off by pressing and holding the Options key with the words “Control Lock Hold 3 Sec” below it for 3 seconds.

How do you get around the lid lock on a Whirlpool washing machine?

How to Bypass a Washing Machine Lid Lock (Without Using a Key) Turn off the washer and unhook the device from the wall outlet. The holding tabs and/or screws that keep the top horizontal panel in place should be identified. Look for the lid lock switch, which is located on the underside of the top panel and at the point where it is integrated into the appliance. Reinstall the cover and reconnect the washing machine to the electrical outlet if it has been disconnected.

How do you unlock a Whirlpool washer that isn’t connected to electricity?

The Duet washer’s door will not open. Manually unlocking the washer may be accomplished by removing the top panel (remove the screws on the rear of the top panel and sliding the top panel back to pull the washer out). Afterwards, with the washer turned off, reach down and pull a little ring on the top of the door lock to manually unlock the door lock.

What is the cause of my Whirlpool washer not starting?

First, check to see if power is being delivered to the electrical outlet. Alternatively, if the electrical outlet is getting electricity but the washer is not starting, it is possible that the power cable is faulty. To detect whether or not the power cable is faulty, a multimeter should be used to test the cord for power. If the power cable is not receiving electricity, it should be replaced.

How do you manually open the door of a Whirlpool front-load washing machine?

Whirlpool Duet Washing Machine Unlocking Instructions Locate the door latch assembly on the right side of the door by reaching up inside the front panel and reaching up inside the front panel. On the bottom of the door latch assembly, look for a teardrop-shaped tab that you may pull out. This button will allow you to manually unlock the door. Gently pull down on the tab approximately a quarter inch or until you hear a clicking sound. The door should be able to be opened.

What exactly does the loc symbol on my Maytag washer mean?

Control Lock is a kind of lock that allows you to control how much you can do with your hands.

What does the loc symbol on a Kenmore washer mean?

There was a problem with the LOC. The “LOC” error code indicates that the door lock has become jammed and that the machine is unable to lock or unlock the door as a result. This error may be caused by a variety of circumstances, ranging from a minor glitch in the system to an inactive solenoid. If the machine is unable to close the door, it will not begin the washing cycle and will instead stop.

What is the best way to unlock my Frigidaire washing machine?

It is possible to fast complete the bypass of the Frigidaire front load washer door latch by pushing and holding the control lock button for five seconds. This should take care of the lock. To interrupt the current wash cycle, press the start/pause button on the control panel. With the washing door open, you should be able to put clothing in or take stuff out without difficulty.

In the case of a Frigidaire professional dishwasher, what does loc stand for?

Mode for preventing children from accessing the computer

ncG1vNJzZmivp6x7r6%2FEq6upp5mjwW%2BvzqZma2hiZ3xxfY6wn5qsXZm8pr%2BMpZpmpZWWu267zWauoaGiob2wu8tmrpqrmJq%2Fb7TTpqM%3D